Emil's Projects & Reviews

OpenHardware & OpenSource

Entries tagged "fm synthesis".

PreenFM2 SMD Version 13th November 2017

This project is a redesign of the open source FM synthesiser PreenFM2 created by Xavier Hosxe.

Improvements from the original version:

This entry has been cut, click to read on.

2 comments. Tags: fm synthesis, synthesiser.
MIDI Note Velocity for Korg Volca FM 4th January 2018

Korg Volca FM is a great little FM synthesizer which also includes a step sequencer.

Korg Volca FM Front Panel

Inside there are 2 PCBs linked together via a 7pin connector. The main PCB has an ARM-CortexM4 which is the core of the whole synthesizer, all waveforms are computed inside this device. The second PCB has the touch sensitive keys and the sequencer LEDs which are all handled by a support microcontroller from Cypress. The two processors are probably talking to each other via the SPI interface (I haven't checked this).

There are 11 + 2 linear potentiometers on this board, each producing an analog voltage between 0-3.3V. These analog voltages are multiplexed and the read directly by two ADCs inputs of the ARM processor. A separate rotary encoder selects the algorithm.

Click on the images bellow to identify all the ICs used in this design:

Korg Volca FM Main PCB Front
Korg Volca FM Main PCB Back
Korg Volca FM Keyboard PCB Back

The integrated circuits and their datasheets used in this device are:

MB9BF164L memory map
Main Flash0x00x40000
Work Flash0x200c00000x8000

There is only one DIN5 connector for MIDI In mainly for saving space but the MIDI Out pins are available and clearly marked on the board if someone wants to solder a second pigtail DIN connector. The MIDI Out is not so important if one doesn't want to use the internal sequencer to drive other instruments.

The touch keys of the Volca FM are not really made for playing, they feel more like toy keys so the great majority of users are playing the synthesizer via MIDI In. Unfortunately there is a major drawback by doing this, the NoteOn velocity parameter is ignored by the Volca. You can still change the velocity of the played notes using the slider potentiometer but you cannot do this remotely.

A firmware update could easily solve this problem but that seems unlikely to happen. Personally I don't see any kind of hardware limitation that pushed Korg to this decision.

There are a few workarounds for this problem. One is to buy the commercial RK-002 MIDI cable which has a programmable microcontroller inside. I don't like this mainly because this cable plus shipping is so expensive that it reaches almost half of the VolcaFM selling price. Another issue is that you have to pay attention to the direction in which you insert this cable.

I opted for a much less expensive mod which uses a little AVR processor. I've chosen an OpenLog board for its small size. You can purchase this board for 3-4$ delivered from various places like AliExpress and EBay.

OpenLog AVR board

The board is about 15×15mm in size and has all the necessary connections routed to .1" pins. The SPI on one side of the board needs to be used to program a special MIDI bootloader which after reset will listen for SysEx messages to load and program the main code running on this AVR chip. The microSD socket on the back of the PCB won't be used and it's better to mask it with tape to prevent any contacts with the components inside the Volca.

The board is small enough to fit near the MIDI In socket, where to optocoupler is located. Just four wires are needed to solder it inside: Vcc and Gnd to ground and 3.3V, Rx to the optocoupler output and Tx to the corresponding serial input of the ARM processor. The original trace between the optocoupler and the ARM processor needs to be cut.

The crystal on the OpenLog board is 16MHz which divides exactly to get the MIDI bitrate of 31250 bauds. The processor main code will intercept all the NoteOn messages "9n kk vv" and send before another Velocity message of "Bn 29 vv" followed by the unchanged NoteOn.

The insertion of this AVR processor will delay all the MIDI messages with about 1ms which is imperceptible. Also to avoid changing the global velocity before each played note first it should compare the new velocity to the previous one and ignore it if it doesn't differ more than +/-5 (velocity ranges from 0-127).

This mod will work for all of the Volca synthesizers series and also has the advantage of easy reprogram the code inside the AVR (bypassing it entirely if so needed) via SysEx messages using a free program like like MIDIOx on PC or SysEx Librarian on Mac OS.

This entry has been cut, click to read on.

One can re-encode the firmware to WAV files using the volca_fw_encode program like this:

$ volca_fw_encode -n FM -b 0 -v 109 volcafm_sys_1_0109RC.bin volcafm_sys_2_0109RC.bin

This will create the following WAV files if you want to update your firmware over the audio cable: volca_sys_1_0109RC.wav and volca_sys_2_0109RC.wav
The volca_fw_encode [v1.2] and volca_fw_decode [v1.2] programs are perfectly reversible and they produce even the WAV file exactly as the Korg's originals.

To dump or program the Volca (or recover from a brick event) connect a J-Link interface to the SwD 6 pin connector and issue the following commands in the cmd line utility (usually JLinkExe):

si swd
speed auto
device MB9BF164L
-- then --
savebin fw_name.bin,0x0,0x40000
--- or ---
loadfile fw_name_1.bin 0x0
loadfile fw_name_2.bin 0x20000
10 comments. Tags: fm synthesis, midi, synthesiser, volca.

RSS Feed